________________________________________________________________________________
John Deere 710G Backhoe Specs
John Deere 710G Engine
Engine Model - John Deere 6068T
Engine type - In-line, 4-cycle
Number of cylinders - 6
Bore and Stroke, mm (in.) - 106 x 127 (4.19 x 5.00)
Displacement, dm3 (in3) - 6.8 (414)
Compression Ratio - 17.0 : 1
Valves per Cylinder – Intake/Exhaust - 1 / 1
Firing Order - 1-5-3-6-2-4
Combustion System - Direct Injection
Aspiration - Turbocharged
Engine Crankcase Vent System - Open
Net peak power - 122 hp (91 kW) @ 2,000 rpm
Net peak torque - 397 lb.-ft. (538 Nm) @ 1,300 rpm
Torque rise - 33 percent
Exhaust System Flow - 24.8 (876)
Coolant Flow, L/min (gal/min) - 174 (46)
Engine Coolant Capacity, L (qt) - 11.3 (12.0)
Recommended Pressure Cap, kPa (psi) - 69 (10)
Minimum Coolant Fill Rate, L/min (gal/min) - 11 (3)
Fuel Injection Pump - Stanadyne
Governor Regulation - 5%
Governor Type - Mechanical
Total Fuel Flow, kg/h (lb/h) - 96 (212)
Oil Pressure at Rated Speed, kPa (psi) - 345 (50)
Oil Pressure at Low Idle, kPa (psi) - 105 (15)
Total Engine Oil Capacity with filter, L (qt) - 19 (20.1)
Battery Capacity (CCA) - 12 Volt System, Amp - 800
Maximum Allowable Starting Circuit Resistance, Ohm - 0.0012
John Deere 710G Drive Train
Transmission Type - Four-speed, helical cut gear, full powershift
transmission with hydraulic reverser
Gears - 4 forward and 3 reverse
Oil capacity - 16 qts (15.1 L)
Chassis - 4WD (MFWD)
Steering type - hydrostatic power
Torque converter - electrically actuated twist grip F-N-R in 1st through
4th gears
Clutch - Electric clutch cutoff on gearshift and loader levers
Differential lock - electric foot-actuated
Final drives - Planetary
JD 710G Hydraulic System
Hydraulic System - Pressure compensated load sensing (PCLS)
Pressure (Backhoe) - 3,625 psi (25 000 kPa)
Pressure Loader - 3,625 psi (25 000 kPa)
Flow @ 2,200 rpm Backhoe/Loader - 52 gpm (197 L/min.)
Hydraulic filter - 6-micron vertical spin-on
Tires
Industrial Front Tires - 15-19.5
Industrial Front Tires - 16.5L-16.1
Industrial Rear Tires - 21L-28
Industrial Rear Tires - 20.5-25
John Deere 710G Backhoe Specifications
Loading height, truck loading position (Std./Ext.) - 14 ft. 3 in. (4340
mm) / 16 ft. (4880 mm)
Reach from center of swing pivot (Std./Ext.) - 22 ft. 6 in. (6860 mm) /
26 ft. 8 in. (8130 mm)
Reach from center of rear axle (Std./Ext.) - 26 ft. 8 in. (8130 mm) / 30
ft. 10 in. (9400 mm)
Maximum digging depth (Std./Ext.) - 17 ft. 10 in. (5440 mm) / 22 ft. 6
in. (6860 mm)
Ground clearance, minimum - 14 in. (356 mm)
Transport height (Std./Ext.) - 13 ft. 8 in. (4170 mm) / 13 ft. 10 in.
(4220 mm)
Overall length, transport - 26 ft. 9 in. (8150 mm)
Stabilizer width – transport with ROPS - 7 ft. 11 in. (2410 mm)
Stabilizer spread – operating - 13 ft. 1 in. (3990 mm)
Stabilizer overall width - 15 ft. 3 in. (4650 mm)
Width over tires - 93.8 in. (2380 mm)
Height to tops of ROPS - 9 ft. 9 in. (2970 mm)
Length from axle to axle - 98.9 in. (2511 mm)
Backhoe boom cylinder (Bore/Stroke/Rod) - 6.30 in. (16 cm) / 37.15 in.
(94,5 cm) / 3.74 in. (9,5 cm)
Backhoe crowd cylinder (Bore/Stroke/Rod) - 5.51 in. (14 cm) / 31.16 in.
(79,2 cm) / 3.35 in. (8,5 cm)
Backhoe bucket cylinder (Bore/Stroke/Rod) - 4.33 in. (11 cm) / 37.09 in.
(94,2 cm) / 2.76 in. (7 cm)
Backhoe swing cylinder (Bore/Stroke/Rod) - 4.33 in. (11 cm) / 12.13 in.
(31 cm) / 2.20 in. (5,6 cm)
Backhoe dipperstick cylinder (Bore/Stroke/Rod) - 3.15 in. (8 cm) / 54.00
in. (137,2 cm) / 1.77 in. (4,5 cm)
Backhoe stabilizer cylinder (Bore/Stroke/Rod) - 4.53 in. (11,5 cm) /
23.15 in. (59 cm) / 2.48 in. (6,3 cm)
John Deere 710G Loader Specifications
Height to bucket hinge pin, maximum - 12 ft. 5 in. (3.78 m)
Dump clearance, bucket at 45 degrees - 9 ft. 4 in. (2.84 m)
Reach at full height, bucket at 45 degrees - 30.3 in. (770 mm)
Digging depth below ground, bucket level - 4.1 in. (104 mm)
Distance from front axle centerline to bucket cutting edge - 86.5 in.
(2198 mm)
Raising time to full height - 4,8 sec.
Bucket dump time at maximum height - 1,3 sec.
Bucket lowering time (power down) - 3,1 sec.
Loader boom cylinder (Bore/Stroke/Rod) - 3.94 in. (10 cm) / 31.99 in.
(81,3 cm) / 2.20 in. (5,6 cm)
Loader bucket cylinder (Bore/Stroke/Rod) - 4.33 in. (11 cm) / 26.44 in.
(67,2 cm) / 2.20 in. (5,6 cm)
JD 710G Capacities
Fuel tank (with ground level fueling) - 69 gal. (261 L)
Hydraulic system - 42 gal. (159 L)
Engine coolant - 28.5 qt. (27 L)
Engine oil including filter - 20 qt. (19 L)
Torque converter and transmission - 16 qt. (15 L)
Rear axle - 4.2 gal. (16 L)
Mechanical front wheel drive axle - 2.8 gal. (10.6 L)
Dimensions
Operating Weight (Two Wheel Drive ROPS) - 23,000 lbs (10432 kg)
Operating Weight (4WD, cab, extentable dipperstick) - 26,500 lbs (12020
kg) (4WD, cab, extentable dipperstick)
Wheelbase - 98.9 inches (251 cm)
Length - 321 inches (815 cm)
Width - 95 inches (241 cm)
Height (ROPS) - 117 inches (297 cm)
Ground clearance - 14 inches (35 cm)
Turning radius - 13 ft. 0 in. (3960 mm)
Bucket clearance circle - 35 ft. 5 in. (10800 mm)
Steering wheel turns, lock to lock - 2.7
________________________________________________________________________________
________________________________________________________________________________________
JOHN DEERE BACKHOE LOADERS SPECIFICATIONS |
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
JOHN DEERE INDUSTRIAL TRACTORS SPECIFICATIONS |
________________________________________________________________________________________
________________________________________________________________________________________