________________________________________________________________________________

John Deere 5510 Specs

John Deere 5510 Engine Specifications

Engine Model - 4045T, Turbocharged
Factory Observed PTO Power - 55.9 kW (75 hp) at 2400 rpm
Maximum Engine Torque - 308 Nm at 1500 rpm
Cylinders Quantity - 4
Bore - 106.5 mm (4.19 in.)
Stroke - 127 mm (5.0 in.)
Displacement - 4.5 L (278 cu. in.)
Compression Ratio - 17.0:1
Cylinder Firing Order - 1-3-4-2
Intake Valve Clearance - 0.35 mm (0.014 in.)
Exhaust Valve Clearance - 0.45 mm (0.018 in.)
Slow Idle Speed - 825-875 rpm
Fast Idle Speed - 2550-2600 rpm
Operating Range Speed - 1600-2400 rpm
Injection Pump Timing Position - 8° BTDC (TimeTrac)
Electrical System - 12-Volt, Negative Ground
Battery Voltage - 12-volt
Cold Cranking Amps - 700 CCA
Open Station BCI Group Size - 28 H
Cab BCI Group Size - 31
Alternator - 40 amps

JD 5510 Transmission

Standard Type - 9/3 CollarShift Transmission
Optional Type - 9/3 SyncShuttle with shiftable 540/540E PTO or 12/12 PowrReverser
Lever Gear Selector - Manual Shift
Brakes - Hydraulically Operated, Wet Disk, Self-Adjusting

Power Take-Off

PTO Type - Standard Fully Independent PTO (540)
Operational SyncShuttle Shiftable - 540/540E Independent
Lever Operated Clutch
Engine-540E (SyncShuttle) Speed - 1700 rpm
Engine-540 Speed - 2400 rpm
Power Take-Off Size - 280 mm (11 in.)

John Deere 5510 Hydraulic System

Type - Open Center Type
Pump Type - Tandem Gear Pump
Steering - Hydrostatic Power Steering
Pump Displacement-Steering - 11.9 cu cm (0.73 cu in.)
Pump Displacement-Implement - 28.8 cu cm (1.76 cu in.)
Steering Flow Rate - 24.9 L/min. (6.6 gpm)
Implement Flow Rate - 62.1 L/min. (16.4 gpm)
Steering (Maximum) Pressure - 12 997-13 500 kPa (130-135 bar) (1885-1955 psi)
Implement (Maximum) Pressure - 18 995-19 692 kPa (190-197 bar) (2755-2855 psi)
Hitch Lift Capacity - 1530 kg (3374 lb)
SCV Flow Rate - 62.1 L/min (16.4 gpm)

Three-Point Hitch

Type - Categories I and II, Top Link Sensing
Standard - Fixed Draft Links with Interchangeable Balls
Optional - Telescopic Draft Links with Interchangeable Balls
Three-Point Hitch Lift Capacity at 610 mm (24 in.) Behind Hitch Balls - 1530 kg (3374 lb)

JD 5510 Capacities

Fuel Tank (Open Station/Cab) - 87 L (18 gal) / 87 L (23 gal)
Cooling System - 10.8 L (11.4 qt)
Crankcase (including filter change) - 8.5 L (9 gal)
Dry Clutch (CollarShift and SyncShuttle Transmission) - 38 L (10 gal)
Wet Clutch (PowrReverser Transmission) - 43.5 L (11.5 gal)
Mechanical Front Wheel Drive (MFWD) Wheel Hubs - 0.6 L (0.6 qt)
MFWD Axle Housing - 5 L (5.2 qt)
MFWD Assembly - 6.2 L (5.7 qt)

John Deere 5510 Tires

Front Tires - 10.5/80-18 10PR
Front Tires - 11.2-24 6PR
Front Tires - 10.8/80-18 10PR
Rear Tires - 16.9-30 6PR
Rear Tires - 18.4-16.1 6PR

JD 5510 Dimensions

Width (with Roll-Gard ROPS/Cab) - 1745 mm (68.7 in.)
Length (less Hitch, Drawbar and Front Weights) - 3510 mm (138.2 in.)
Height from Ground-to-Top of Hood - 1501 mm (59.1 in.)
Height from Ground-to-Top of Steering Wheel - 1697 mm (66.8 in.)
Height from Ground-to-Top of Roll-Gard ROPS - 2482 mm (97.7 in.)
Height from Ground-to-Top of Folded ROPS - 2024 mm (79.7 in.)
Height from Ground-to-Top of Cab - 2550 mm (100.4 in.)
Height from Ground-to-Top of Drawbar - 478 mm (18.8 in.)
Height from Ground-to-Crop Clearance-Front Axle - 391 mm (15.4 in.)
Centerline of Rear Axle to Folded ROPS - 1328 mm (52.3 in.)
Centerline of Rear Axle to Cab - 1854 mm (73 in.)
Wheelbase - 2177 mm (85.7 in.)
Rear Axle Diameter - 76.2 mm (3 in.)
Turning Radius with Brakes - 3.54 m (11.6 ft)
Turning Radius without Brakes - 3.93 m (12.9 ft)
Weight - 2785 kg (6140 lb)