________________________________________________________________________________

John Deere 4100 Attachments

John Deere 4100 Front End Loader

410 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4100
Bucket Width - 1250 mm (49 in.)
Bucket Length - 618 mm (24.3 in.)
Bucket Mass - 70 kg (154 lb)
Hydraulic System Rated Flow - 27.7 L/Min (7.3 gal/min)
Maximum Pressure - 16.67 MPA (2418 psi)
Maximum Lift Height To Pivot Pin - 1879 mm (74 in.)
Bucket Level Clearance - 1722 mm (68 in.)
Bucket Dumped Clearance - 1400 mm (55 in.)
Overall Length - 3119 mm (123 in.)
Digging Depth - 152 mm (6 in.)
Reach At Max Lift Height - 629 mm (24.8 in.)
Bucket Reach on Ground - 1133 mm (44.6 in.)
Max Dump Angle - 45°
Max Dump Angle at Ground - 123°
Max Rollback Angle - 25°
Rollback Angle at Full Height (SAE) - 64°
Overall Height In Carry Position - 1171 mm (46 in.)
Lift Capacity To Max Height at Pivot Point - 400 kg (882 lb)
Lift Capacity To Max Height - 280 kg (618 lb)
Lift Capacity To 1.5 m (59 in.) at Pivot Point - 486 kg (1072 lb)
Lift Capacity To 1.5 m (59 in.) - 355 kg (781 lb)
Lift Capacity With Forklift to Max Height - 125 kg (276 lb)
Breakout Force At Pivot Point - 10037 N
Breakout Force At 500 mm (19.7 in.) Forward of Pivot Point - 6668 N
Bucket Rollback Force At Max Height - 8263 N
Bucket Rollback Force At 1.5 m (59 in.) Lift Height - 9632 N
Bucket Rollback Force At Ground Level Line - 7387 N

Install Hydraulic Hoses - Install nylon protector sleeve (flared end first) over four hoses. Connect hoses to fittings. Tighten to specification. Hose-to-Line Fittings Torque - 38 Nm (28 lb-ft). Install color-coded dust cap on each coupler to match function as follows: Doubling of sleeve is done by attaching sleeve to hoses with tie band approximately 50 mm (2 in.) from fittings, then folding the sleeve inside itself. Double sleeve about 150 mm (6 in.) and cover fittings. Install tie band by lacing tie band through holes in protective sleeve. Press lines into clamp and
tighten cap screw to secure lines to boom. Pull sleeve toward quick-couplers, attach with tie band, double about 50 mm (2 in.) and install second tie band lacing it through protective sleeve. Secure sleeve to hoses with tie bands. After 410 loader has been mounted on JD 4100 tractor, route hoses to avoid contact with loader frame at location. Using tie band, secure hose bundle to loader frame.

John Deere 4100 Backhoe

46 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 4100
Digging Depth - 1,98m (78 in.)
Swing Arc - 180 degrees
Weight - 407kg (896 lb)
Loading Height (bucket at 60°) - 1,5m (60 in.)
Reach From Center Line of Swing Pivot - 2,57m (101 in.)
Transport Height - 1,5m (60 in.)
Bucket Rotation - 180 degrees
Loading Reach (bucket at 60°) - 97cm (38 in.)
Transport Overhang - 1,04m (41 in.)
Undercut - 71cm (28 in.)
Stabilizers Spread Width (Raised) - 1,19m (47 in.)
Stabilizers Spread Width (Lowered) - 1,98m (78 in.)
Boom Lift Capacity - 158kg (348 lb)
SAE Dipperstick Digging Force - 5,56kN (1250 lb)
SAE Bucket Digging Force - 10,90kN (2450 lb)
Bucket Control Main Relief Valve Pressure - 15,51mPa (2250 psi)

Attaching 46 Backhoe To JD 4100 Tractor - Front hanger end of subframe must be below level of front hanger on tractor before tractor is positioned. Back tractor into position over backhoe subframe. Connect backhoe hydraulic hoses: Disconnect Power Beyond hose from female coupler and connect to backhoe hose. Connect backhoe hose with male coupler to female coupler. Start engine and run at slow idle. Use stabilizer control levers to raise or lower stabilizers as needed to position hooks on 46 backhoe subframe in line with draft link pins on tractor rear mounting
support. Back tractor until subframe hooks seat firmly into draft link pins. Lock tractor park brake. Remove backhoe boom lock pin. Use boom and stabilizer control levers to alternately raise the boom and stabilizers, pivoting the subframe on the draft link pins until the holes in the subframe front end align with holes in front hanger.

John Deere 4100 Snowblower

47" Snowblower Specifications

Type - 2-Stage, Front Mount
Compatibility - JD 4100
Width - 1194 mm (47-in.)
Height of Opening - 584 mm (23-in.)
Housing Thickness - 14 ga (0.075-in.)
Side Panel Thickness - 7 ga (0.177-in.)
Auger Diameter - 16-in. (406 mm)
Auger Speed - 160 rpm at rated engine speed.
Impeller Speed - 800 rpm at rated engine speed.
Impeller Diameter - 406 mm (16-in.)
Lift System - Hydraulic
Lift Height - 191-203 mm (7-1/2-8 in.)
Chute Control - Hydraulic
Chute Rotation - 200 Degrees
Weight (Approximate) - 181 kg (400 lb)

John Deere 4100 Mower Deck

54-Inch Mower Deck Specifications

Type - Mid-Mount
Compatibility - JD 4100
Cutting Width - 137.2 cm (54 in.)
Number of Blades - 3
Spindles - 20 mm (0.75 in.)
Weight - 85 kg (190 lb)
Gear Case Grease Volume - 0.5 L (1 pt)
Input Shaft End Play - 0.0-0.06 mm (0.0-0.002 in.)
Output Shaft End Play - 0.0-0.03 mm (0.0-0.001 in.)
1/4 In. Diameter Pipe Plugs Torque - 14-25 Nm (120-216 lb-in.)
Breather (1/8 diameter pipe plugs) Torque - 7-10 Nm (60-90 lb-in.)
Blade Bolt Torque - 57 - 84 Nm (42-62 lb-ft)

60-Inch Mower Deck Specifications

Type - Mid-Mount
Compatibility - JD 4100
Cutting Width - 152.4 cm (60 in.)
Number of Blades - 3
Spindles - 25.4 mm (1.0 in.)
Weight - 147 kg (325 lb)
Gear Case Grease Volume - 240 ml (8 oz)
Input Shaft End Play - 0.0-0.06 mm (0.0-0.002 in.)
Output Shaft End Play - 0.0-0.03 mm (0.0-0.001 in.)
Blade Bolt Torque - 102-123 Nm (75-91 lb-ft)

261 Mower Specifications

Type - Rear Mount
Compatibility - JD 4100
CuttingWidth - 152 cm (60 in.)
Cutting Height - 51-152 mm (2-6 in.)
Number of Blades - 3
Belt - B-Section
Gear Case Grease Volume 3-point Hitch Mower - 0.5 L (1 pt)
Mounting - Category 1
PTO Speed - 540 rpm
Weight - 168 kg (370 lb)

261 Mower Spindle Assembly - Clean threads on shaft and hub using clean and cure primer. Apply thread lock and sealer (medium strength) on threads. Install hub on shaft. Tighten to 163 Nm (120 lb-ft). Install snap rings. Pack both bearings with Multi-Purpose Grease or equivalent. Turn housing bottom-side up to install lower bearing (sealed on one side only). Be sure bearing seal faces up. Press bearing against snap ring using a 1-15/16 in. disk. Apply Multi-Purpose Grease or equivalent to area between snap rings. Put spacer against lower bearing. Be sure there is enough grease to hold spacer centered in bore. Turn housing top-side-up to install upper nonsealed bearing. Press bearing against spacer, using the correct size driver. Support both the inner and outer rings of both upper and lower bearings.

Put housing bottom-side-up on a press plate with a 1-1/16 in. hole or gap so upper bearing is centered over hole or gap. Look inside spindle to be sure spacer aligns with bearings inside housing and hole or gap of press plate, then install hub and shaft assembly. Press shaft through both bearings and spacer until hub stops against lower bearing. Turn spindle over to install top seal. Press seal flush with rim of housing, using a 1-7/8 in. OD pipe for a driver. Coat outer surface of bushing with grease before you install it with notch toward bearing. Install key. Be sure key is seated to prevent metal shavings from contaminating bearings. Install sheave with welded side of hub away from bearing. Hold spindle assembly in a vise by the lower hub to install nut. Tighten nut to 163 Nm (120 lb-ft). Turn casting on spindle to check for free spin. Install grease fitting. Fill spindle housing completely with Multi-Purpose grease or equivalent.