________________________________________________________________________________

John Deere 4310 Attachments

John Deere 4310 Front End Loader

420 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4310
Height (to pin) - 87.6 in. (222 cm)
Clearance, dumped bucket - 66.1 in. (167 cm)
Dump reach - 30.3 in. (76 cm)
Dump angle - 43
Reach at ground - 53.6 in. (136 cm)
Rollback angle - 23
Breakout force (at pin) - 2693 lb (1221 kg)
Lift to full height (at pin) - 1195 lb (542 kg)
Lift to full height (at 500 mm) - 895 lb (405 kg)
Raise time to height - 2.9 s
Bucket dump time - 1.6 s
Lowering time - 2.4 s
Rollback time - 2.2 s

Checking and Adjusting Latch Plate and Locking Lever - Lower 420 loader to the ground and apply enough downward force to relieve weight from tires. Rotate latch plate over weight bracket, it should rotate freely. Check for interference at location. Grind or file material to eliminate any obstruction. Latch lever must be in hole and free to move up and down. Using tape measure through hole, measure distance from weight bracket-to-front surface of latch. It should be no more than specification. If pin is tight in hole or is still in slot with latch plate closed, adjust latch rod: Remove cap screw to disconnect lever from pin. Rotate pin (in or out) on rod until pin fits freely in hole and dimension at latch and weight bracket is within specification. Weight Bracket-to-Front Surface of Latch - 13 mm (0.5 in.). Apply thread lock and sealer (high strength) to threads of cap screw. Attach lever to pin in reverse order as disassembled.

430 Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4310
Bucket Width - 61" (1550 mm)
Breakout @ Pivot - 3299 Lbs. (14676N)
430 Loader Lift Height - 101.4" (2575 mm)
Rollback Angle - 30 Degrees
Dump Angle - 45 Degrees
Lift Capacity To Max Height at Pivot Point - 572 kg (1258 lbs)
Lift Capacity To Max Height - 475 kg (1045 lbs)
Lift Capacity To 1.5 m (59 in.) at Pivot Point - 883 kg (1943 lbs)
Lift Capacity To 1.5 m (59 in.) - 765 kg (1687 lbs)
Lift Capacity With Forklift to Max Height - 345 kg (760 lbs)
Breakout Force At Pivot Point - 14676 N (3299 lbf)
Breakout Force At 500 mm (19.7 in.) Forward of Pivot Point - 10750 N (2417 lbf)
Bucket Rollback Force At Max Height - 9587 N (2155 lbf)
Bucket Rollback Force At 1.5 m (59 in.) Lift Height - 14898 N (3349 lbf)
Bucket Rollback Force At Ground Level Line - 13293 N (2988 lbf)
Quik-Tatch Parking - Yes
Quik-Change Attachment - Yes

300CX Loader Specifications

Type of Attachment - Front End Loader
Compatibility - John Deere 4310
Lifting capacity at pivot pin (maximum height) - 1393 lb. (633 kg)
Lifting capacity at 0.5 m ahead of pivot pin - 1005 lb. (457 kg)
Lifting capacity to 59 in. at pivot pin - 2109 lb. (959 kg)
Lifting capacity to 59 in. at 0.5 m ahead - 1639 lb. (745 kg)
Maximum Lifting height at pivot pin - 103,3 in. (2,62 m)
Reach at maximum height - 30,1 in. (0,77 m)
Breakout force at pivot pin - 3769 lbf. (16771N)
Dump angle - 49,3 degrees
Rollback angle - 23,8 degrees
300CX Loader raising/lowering time - 3,6/2,1 sec.
Bucket dump time/regen - 3,0/1,16 sec.
Bucket rollback time - 1,8 sec.

John Deere 4310 Backhoe

48 Backhoe Specifications

Type of Attachment - Backhoe
Compatibility - John Deere 4310
Digging Depth - 2,59 m (102 in.)
Weight With Large Frame Adapter - 1517 kg (690 lb)
Weight With Medium Frame Adapter - 1477 kg (671 lb)
Swing Arc - 180 degrees
Loading Height (bucket at 60°) - 2,08 m (82 in.)
Reach From Center Line of Swing Pivot - 3,38 m (133 in.)
Transport Height - 2,1 m (81 in.)
Bucket Rotation - 180 degrees
Loading Reach (bucket at 60°) - 1,09 cm (43 in.)
48 Backhoe Transport Overhang - 1,22 m (48 in.)
Undercut - 86 cm (34 in.)
Stabilizers Spread Width (Raised) - 1,37 m (54 in.)
Stabilizers Spread Width (Lowered) - 2,51 m (99 in.)
Boom Lift Capacity - 345 kg (760 lb)
SAE Dipperstick Digging Force - 10,83 kN (2435 lb)
SAE Bucket Digging Force - 16,59 kN (3730 lb)
Bucket Control Main Relief Valve Pressure - 17,58 mPa (2550 psi)

John Deere 4310 Snowblower

59-inch Snowblower Specifications

Type - Front Mount, 2-Stage
Compatibility - JD 4310
Width - 1499 mm (59-in.)
Height of Opening - 584 mm (23-in.)
Housing Thickness - 14 ga (0.075-in.)
Side Panel Thickness - 7 ga (0.177-in.)
Auger Diameter - 16-in. (406 mm)
Auger Speed - 160 rpm at rated engine speed.
Impeller Speed - 800 rpm at rated engine speed.
Impeller Diameter - 406 mm (16-in.)
Lift System - Hydraulic
Lift Height - 191-203 mm (7-1/2-8 in.)
Chute Control - Hydraulic
Chute Rotation - 200 Degrees
Weight (Approximate) - 201 kg (450 lb)

John Deere 4310 Blade

72" Rear Blade Specifications

Model - Frontier RB1072
Type - Rear Mount
Compatibility - JD 4310
Working Width - 72" (183 cm)
Operating Weight (Mass) - 283 lbs (128 kg)
Tractor Size - 12 to 30 hp (9 to 22 kW)
3-Point Hitch - Category 1
Implement Code for Tractor Ballast - 16.2
Offset - None 12" (30 cm) right or left
Angle 360° - Locks at 0°, 15°, 30° forward right or left
Blade Tilt - 0°, 15° either side
Pitch Adjustment - In top link of tractor 3-point hitch

72" Front Blade Specifications

Model - Frontier AF11E
Type - Loader Mounted
Width - 182.9 cm (72 in.)
Height - 58.4 cm (23 in.)
Depth - 86.4 cm (34 in.)
Cutting width - 182.9 cm (72 in.)
Current Loaders series style - 300, 400, 500
Operational Weight - 181.4 kg (400 lb)
Shipping Weight - 195 kg (430 lb)
Moldboard Thickness - 10 gauge 3.4 mm (0.13 in.)
Moldboard Height - 58.9 cm (23.2 in.)
Angle/Pivot Standard adjustment - Manual
Angle/Pivot Degrees (each side) - 30
Skid Shoes - Standard

John Deere 4310 Mower Deck

72-Inch 7-Iron Mower Deck Specifications

Model - 72" 7-Iron Mid-Mount Mower Deck
Mower Type - Mulch or Side Discharge
Compatibility - JD 4310
Cutting Blades - 3
Overall Width - 1.05 m (41.5 in.)
Overall Length - 2.19 m (86 in.)
Cutting Height - 2.5-23 cm (1-9 in.)
Cutting Width - 1.8 m (72.8 in.)
Mower Weight (Large Chassis Mower) - 150 kg (331 lb)
Mower Weight (Mid Chassis Mower) - 156 kg (345 lb)
Blade Bolt Torque - 122 Nm (90 lb-ft)
Gearbox Oil Capacity - 136 ml (4.6 oz)

Install 72" Mid-Mount Mower Bracket - Remove JD 4310 tractor MFWD bracket: Locate MFWD cable and bracket, at left side of transmission. Remove and retain cotter pin and flat washer securing MFWD cable to shift lever at transmission. Remove and retain locking clip securing MFWD cable in existing MFWD bracket, and remove cable from slot in bracket. Remove and retain the M8x45 capscrew and M8 locknut, securing the hydraulic line and clamp to the MFWD bracket. Remove and discard two M10x20 capscrews, securing the MFWD bracket to the
transmission, then remove and discard the bracket.

Install mid-mount mower bracket: Position the mid-mount mower bracket, with the upper two mounting holes aligned with the two holes that secured the MFWD bracket to the transmission, and with the hydraulic line and clamp over another mounting hole. Secure the bracket with three M10x25 capscrews, and one M12x25 capscrew. Tighten hardware. Secure the hydraulic line and clamp with the M8x45 capscrew and M8 locknut. Tighten hardware. Install MFWD cable into slot in mower bracket and secure with clip. Install cable end into shift lever, and secure with flat washer and cotter pin.

60-Inch 7-Iron Mower Deck Specifications

Model - 60" 7-Iron Mid-Mount Mower Deck
Mower Type - Mulch or Side Discharge
Compatibility - JD 4310
Cutting Blades - 3
Overall Width - 1.5 m (61.3 in.)
Cutting Height - 2.5-15.2 cm (1-6 in.)
Cutting Width - 1.5 m (60.9 in.)
Mower Weight - 147 kg (324 lb)
Blade Bolt Torque - 122 Nm (90 lb-ft)
Gearbox Oil Capacity - 136 ml (4.6 oz)

Servicing 60-inch Mower Belt

Removing Belt - Remove mower from machine. Remove six locking rings, three locking knobs and shields. Clean area under shields. Loosen jam nut and turn threaded adjuster bolt to relieve spring tension. Roll the belt off the left sheave. Remove four nuts and washers. Remove gearbox bracket with gearbox. Remove belt. Installing Belt - Install belt around three sheaves. Route belt. Remove belt from left sheave. Route belt around gearbox sheave as you install gearbox bracket on four bolts. Install four washers and nuts. Roll the belt onto left sheave. Tighten threaded adjuster bolt and jam nut. Check belt tension. Install shields with six locking rings and three locking knobs.

Checking and Adjusting Belt Tension (60-Inch Mower) - Remove mower from machine. Pull sideways on belt and see how much the belt tensioner rod moves within the threaded adjuster bolt. If there is more than 10 mm (0.4 in.) rod movement, adjust the belt tension. Loosen the jam nut. Tighten the adjuster bolt by turning clockwise just enough to compress the spring. Tighten jam nut.

John Deere 4310 Rotary Broom

52-Inch Rotary Broom Specifications

Overall Height - 48 cm (19 in.)
Overall sweeping width when angled 0° - 1.3 m (52 in.)
Overall sweeping width when angled 27° left or right - 1.2 m (48 in.)
Brush Diameter - 53 cm (21 in.)
Weight (Broom Only) - 109 kg (240 lb)
Shipping Weight - 139 kg (306 lb)
Brush Material - Polypropylene
Sweeping Height - 9 Positions in 13mm (1/2 in.) Increments
Angling - 0-27° Each Side
Angling Method - Hydraulic
Speed - 220 rpm
Caster Wheels - 160x80 mm (6-1/4 x 3-1/4 in.)
Brush Drive - Front PTO
Broom Gearbox - Reduction 3 to 1, Straight Bevel Gear, Shear Pin Protected

Install PTO Shaft - Remove one 5.7 cm (2.25 in.) shear bolt and locknut stored at back side of 52-inch broom. Position PTO shaft support. Slide PTO shaft onto broom stubshaft. Align hole in PTO shaft with hole in stubshaft. Install shear bolt and locknut.

Installing Ballast - If added traction is required while operating 52" broom: Install chains on drive tires. Use traction assist. Install wheel weights on drive wheels or use liquid ballast in drive tires.

Closing SCV Lockout Valve - Remove mower deck. Turn the lift adjustment stop dial on mower to highest position. Start the engine. Raise mower lift arms completely using the upper hydraulic control lever. Park machine safely. Turn SCV lockout valve clockwise completely to close the valve. This prevents hydraulic flow to mower and rear implement lift and directs full pressure to the broom hydraulic circuits for best performance.